Filter Results:
Filter by Pivot Size:
Filter by Material:
Filter by Head:
Filter by Head Diameter:
Filter by Threads:
Filter by Length:
Folder Pivots
 More Information |
Pivot Size | Material |
| .125″ | 416 SS | |
| Head | Head Dia | |
| Flat Head | .373″ | |
| Threads | Length | |
| 2-56 | .500″ |
| # Pcs | Price | Quantity | Stock |
|---|
| 1 | $5.40 |
-
+
|
27 | ||
| 10 | $42.80 |
-
+
|
27 | ||
| 100 | $385.20 |
-
+
|
4 |
Precision Machined .125" Flat Head Pivot
| Shaft Diameter: | .1245" |
| Shaft Tolerance: | +-.0002" |
| Shaft Length: | .500" |
| Screw Size: | 2-56 |
| Heat Treated: | Yes |
| Head Type: | Flat |
| Head Diameter: | .373" |
| Head Thickness: | .125" |
| Material: | 416 Stainless |
Our pivots have the tightest tolerances and are more consistent than any pivot available. We first sold precision machined pivots in 2007. The shaft tolerances on all our pivots is +-.0002" and we maintain those tolerances today.
The most important attribute of all our pivots is consistency. If any of our pivots are damaged, a replacement pivot can be installed in a few minutes and they always fit. We've been told this multiple times.
On the shaft below the head is a .0005" raised area or ring. The purpose of the ring is to a create friction fit between the liner/frame and pivot. The fit is tight enough to prevent the pivot from turning, but allows easy removal. We recommend reaming, not drilling, the blade and liners, to .1250" diameter. The pivot will pop into the liner/frame and not move if the hole is properly reamed to the correct diameter.
The shaft is threaded 2-56. The fine pitch of the threads make it easy to adjust the blade tension.
 More Information |
Pivot Size | Material |
| .125″ | 416 SS | |
| Head | Head Dia | |
| – | – | |
| Threads | Length | |
| 2-56 | .500″ |
| # Pcs | Price | Quantity | Stock |
|---|
| 1 | $4.40 |
-
+
|
22 | ||
| 10 | $35.00 |
-
+
|
29 | ||
| 100 | $315.00 |
-
+
|
5 |
Precision Machined .125" Barrel Pivot
| Shaft Diameter: | .1245" |
| Shaft Tolerance: | +-.0002" |
| Shaft Length: | .500" |
| Screw Size: | 2-56 |
| Heat Treated: | Yes |
| Material: | 416 Stainless |
Our pivots have the tightest tolerances and are more consistent than any pivot available. We first sold precision machined pivots in 2007. The shaft tolerances on all our pivots is +-.0002" and we maintain those tolerances today.
The most important attribute of all our pivots is consistency. If any of our pivots are damaged, a replacement pivot can be installed in a few minutes and they always fit. We've been told this multiple times.
The barrel pivots are threaded from one end all the through. They are not threaded from each end like some barrel pivots. The difference is pivots threaded from each end will almost never match where they meet inside the pivot. The result is a cross threaded screw. You will never have this problem with our barrel pivots.
The shaft is threaded 2-56. The fine pitch of the threads make it easy to adjust the blade tension.
 More Information |
Pivot Size | Material |
| .125″ | 416 SS | |
| Head | Head Dia | |
| Dome Head | .290″ | |
| Threads | Length | |
| 2-56 | .500″ |
| # Pcs | Price | Quantity | Stock |
|---|
| 1 | $5.40 |
-
+
|
35 | ||
| 10 | $42.80 |
-
+
|
29 | ||
| 100 | $385.20 |
-
+
|
5 |
Precision Machined .125" Dome Head Pivot
| Shaft Diameter: | .1245" |
| Shaft Tolerance: | +-.0002" |
| Shaft Length: | .500" |
| Screw Size: | 2-56 |
| Heat Treated: | Yes |
| Head Type: | Dome |
| Head Diameter: | .290" |
| Head Thickness: | .125" |
| Material: | 416 Stainless |
Our pivots have the tightest tolerances and are more consistent than any pivot available. We first sold precision machined pivots in 2007. The shaft tolerances on all our pivots is +-.0002" and we maintain those tolerances today.
The most important attribute of all our pivots is consistency. If any of our pivots are damaged, a replacement pivot can be installed in a few minutes and they always fit. We've been told this multiple times.
On the shaft below the head is a .0005" raised area or ring. The purpose of the ring is to a create friction fit between the liner/frame and pivot. The fit is tight enough to prevent the pivot from turning, but allows easy removal. We recommend reaming, not drilling, the blade and liners, to .1250" diameter. The pivot will pop into the liner/frame and not move if the hole is properly reamed to the correct diameter.
The shaft is threaded 2-56. The fine pitch of the threads make it easy to adjust the blade tension.
 More Information |
Pivot Size | Material |
| .187″ | 17-4 SS | |
| Head | Head Dia | |
| Flat Head | .373″ | |
| Threads | Length | |
| 6-64 | .500″ |
| # Pcs | Price | Quantity | Stock |
|---|
| 1 | $5.40 |
-
+
|
27 | ||
| 10 | $42.80 |
-
+
|
16 | ||
| 100 | $385.20 |
-
+
|
4 |
Precision Machined .187" Flat Head Pivot
| Shaft Diameter: | .1870" |
| Shaft Tolerance: | +-.0002" |
| Shaft Length: | .500" |
| Screw Size: | 6-64 |
| Heat Treated: | Yes |
| Head Type: | Flat |
| Head Diameter: | .373" |
| Head Thickness: | .125" |
| Material: | 17-4 Stainless |
Our pivots have the tightest tolerances and are more consistent than any pivot available. We first sold precision machined pivots in 2007. The shaft tolerances on all our pivots is +-.0002" and we maintain those tolerances today.
The most important attribute of all our pivots is consistency. If any of our pivots is damaged, a replacement pivot can be installed in a few minutes and they always fit. We've been told this multiple times.
On the shaft below the head is a .0005" raised area or ring. The purpose of the ring is to a create friction fit between the liner/frame and pivot. The fit is tight enough to prevent the pivot from turning, but allows easy removal. We recommend reaming, not drilling, the blade and liners, to .1875" diameter. The pivot will pop into the liner/frame and not move if the hole is properly reamed to the correct diameter.
The shaft is threaded 6-64. The fine pitch of the threads make it easy to adjust the blade tension. We were the first supplier to make pivots and screws with 64 thread per inch. Other suppliers have followed our lead.
 More Information |
Pivot Size | Material |
| .187″ | 17-4 SS | |
| Head | Head Dia | |
| – | – | |
| Threads | Length | |
| 6-64 | .625″ |
| # Pcs | Price | Quantity | Stock |
|---|
| 1 | $4.40 |
-
+
|
29 | ||
| 10 | $35.00 |
-
+
|
20 | ||
| 100 | $315.00 |
-
+
|
2 |
Precision Machined .187" Barrel Pivot
| Shaft Diameter: | .1870" |
| Shaft Tolerance: | +-.0002" |
| Shaft Length: | .625" |
| Screw Size: | 6-64 |
| Heat Treated: | Yes |
| Material: | 17-4 Stainless |
Our pivots have the tightest tolerances and are more consistent than any pivot available. We first sold precision machined pivots in 2007. The shaft tolerances on all our pivots is +-.0002" and we maintain those tolerances today.
The most important attribute of all our pivots is consistency. If any of our pivots are damaged, a replacement pivot can be installed in a few minutes and they always fit. We've been told this multiple times.
The barrel pivots are threaded from one end all the through. They are not threaded from each end like some barrel pivots. The difference is pivots threaded from each end will almost never match where they meet inside the pivot. The result is a cross threaded screw. You will never have this problem with our barrel pivots.
The shaft is threaded 6-64. The fine pitch of the threads make it easy to adjust the blade tension. We were the first supplier to make pivots and screws with 64 thread per inch. Other suppliers have followed our lead.
 More Information |
Pivot Size | Material |
| .187″ | 17-4 SS | |
| Head | Head Dia | |
| Dome Head | .290″ | |
| Threads | Length | |
| 6-64 | .500″ |
| # Pcs | Price | Quantity | Stock |
|---|
Precision Machined .187" Dome Head Pivot
| Shaft Diameter: | .1870" |
| Shaft Tolerance: | +-.0002" |
| Shaft Length: | .500" |
| Screw Size: | 6-64 |
| Heat Treated: | Yes |
| Head Type: | Dome |
| Head Diameter: | .290" |
| Head Thickness: | .125" |
| Material: | 17-4 Stainless |
Our pivots have the tightest tolerances and are more consistent than any pivot available. We first sold precision machined pivots in 2007. The shaft tolerances on all our pivots is +-.0002" and we maintain those tolerances today.
The most important attribute of all our pivots is consistency. If any of our pivots are damaged, a replacement pivot can be installed in a few minutes and they always fit. We've been told this multiple times.
On the shaft below the head is a .0005" raised area or ring. The purpose of the ring is to a create friction fit between the liner/frame and pivot. The fit is tight enough to prevent the pivot from turning, but allows easy removal. We recommend reaming, not drilling, the blade and liners, to .1875" diameter. The pivot will pop into the liner/frame and not move if the hole is properly reamed to the correct diameter.
The shaft is threaded 6-64. The fine pitch of the threads make it easy to adjust the blade tension. We were the first supplier to make pivots and screws with 64 thread per inch. Other suppliers have followed our lead.
 More Information |
Pivot Size | Material |
| .250″ | 416 SS | |
| Head | Head Dia | |
| Flat Head | .475″ | |
| Threads | Length | |
| 8-64 | .550″ |
| # Pcs | Price | Quantity | Stock |
|---|
| 1 | $5.90 |
-
+
|
31 | ||
| 10 | $46.70 |
-
+
|
34 | ||
| 100 | $420.30 |
-
+
|
4 |
Precision Machined .250" Flat Head Pivot
| Shaft Diameter: | .2450" |
| Shaft Tolerance: | +-.0002" |
| Shaft Length: | .550" |
| Screw Size: | 8-64 |
| Heat Treated: | Yes |
| Head Type: | Flat |
| Head Diameter: | .475" |
| Head Thickness: | .125" |
| Material: | 17-4 Stainless |
Our pivots have the tightest tolerances and are more consistent than any pivot available. We first sold precision machined pivots in 2007. The shaft tolerances on all our pivots is +-.0002" and we maintain those tolerances today.
The most important attribute of all our pivots is consistency. If any of our pivots are damaged, a replacement pivot can be installed in a few minutes and they always fit. We've been told this multiple times.
On the shaft below the head is a .0005" raised area or ring. The purpose of the ring is to a create friction fit between the liner/frame and pivot. The fit is tight enough to prevent the pivot from turning, but allows easy removal. We recommend reaming, not drilling, the blade and liners, to .2500" diameter. The pivot will pop into the liner/frame and not move if the hole is properly reamed to the correct diameter.
The shaft is threaded 8-64. The fine pitch of the threads make it easy to adjust the blade tension. We were the first supplier to make pivots and screws with 64 thread per inch. Other suppliers have followed our lead.
 More Information |
Pivot Size | Material |
| .250″ | 416 SS | |
| Head | Head Dia | |
| Flat Head | .373″ | |
| Threads | Length | |
| 8-64 | .625″ |
| # Pcs | Price | Quantity | Stock |
|---|
| 1 | $5.90 |
-
+
|
27 | ||
| 10 | $46.70 |
-
+
|
28 | ||
| 100 | $420.30 |
-
+
|
5 |
Precision Machined .250" Flat Head Pivot
| Shaft Diameter: | .2450" |
| Shaft Tolerance: | +-.0002" |
| Shaft Length: | .625" |
| Screw Size: | 8-64 |
| Heat Treated: | Yes |
| Head Type: | Flat |
| Head Diameter: | .373" |
| Head Thickness: | .125" |
| Material: | 416 Stainless |
Our pivots have the tightest tolerances and are more consistent than any pivot available. We first sold precision machined pivots in 2007. The shaft tolerances on all our pivots is +-.0002" and we maintain those tolerances today.
The most important attribute of all our pivots is consistency. If any of our pivots are damaged, a replacement pivot can be installed in a few minutes and they always fit. We've been told this multiple times.
On the shaft below the head is a .0005" raised area or ring. The purpose of the ring is to a create friction fit between the liner/frame and pivot. The fit is tight enough to prevent the pivot from turning, but allows easy removal. We recommend reaming, not drilling, the blade and liners, to .2500" diameter. The pivot will pop into the liner/frame and not move if the hole is properly reamed to the correct diameter.
The shaft is threaded 8-64. The fine pitch of the threads make it easy to adjust the blade tension. We were the first supplier to make pivots and screws with 64 thread per inch. Other suppliers have followed our lead.
 More Information |
Pivot Size | Material |
| .250″ | 17-4 SS | |
| Head | Head Dia | |
| – | – | |
| Threads | Length | |
| 8-64 | .625″ |
| # Pcs | Price | Quantity | Stock |
|---|
| 1 | $4.90 |
-
+
|
26 | ||
| 10 | $38.90 |
-
+
|
38 | ||
| 100 | $350.10 |
-
+
|
5 |
Precision Machined .250" Barrel Pivot
| Shaft Diameter: | .2450" |
| Shaft Tolerance: | +-.0002" |
| Shaft Length: | .625" |
| Screw Size: | 8-64 |
| Heat Treated: | Yes |
| Material: | 17-4 Stainless |
Our pivots have the tightest tolerances and are more consistent than any pivot available. We first sold precision machined pivots in 2007. The shaft tolerances on all our pivots is +-.0002" and we maintain those tolerances today.
The most important attribute of all our pivots is consistency. If any of our pivots are damaged, a replacement pivot can be installed in a few minutes and they always fit. We've been told this multiple times.
The barrel pivots are threaded from one end all the through. They are not threaded from each end like some barrel pivots on the market. The difference is pivots threaded from each end will almost never match where they meet inside the pivot. The result is a cross threaded screw. You will never have this problem with our barrel pivots.
The shaft is threaded 8-64. The fine pitch of the threads make it easy to adjust the blade tension. We were the first supplier to make pivots and screws with 64 thread per inch. Other suppliers have followed our lead.
