.080″ Blade Material

80CrV2 Carbon Steel Information and Composition

Condition:
Our 80CrV2 has been properly annealed and is in the soft condition. You do not have to do any non-standard wasteful processes before heat treating. The steel must be heat treated to get to a hardened state. Follow the heat treat recipe and the steel will harden.

Ratings:
57 = Maximum Toughness
NT = Maximum Edge Holding

The rating scale is 0-100, 0 being minimum and 100 being maximum. The ratings are the maximum potential of the alloy. If the value shown is "NT", the testing has not been performed. I do not recommend heat treating to the maximum value. Choose a heat treat recipe that results in the attributes you want.

Thank you to Dr Larrin Thomas for all the testing he performed and information he has provided. Buy his book Knife Engineering to learn more about knifemaking.

Description:
We started selling this steel in 2006. Several knifemakers were confused by the name 80CrV2 and thought it was an alloy from China. To eliminate confusion we changed the name to 1080+. At that time and for years afterward, we were the only supplier selling this steel. Other suppliers have followed our lead and are now stocking this steel.

This steel is similar to the composition of 1080 with the addition of small amounts of chromium and vanadium. It has tight specifications and is a good steel to use for knives.

We do not disclose the mill where this alloy is made. The mill is located in Europe and has very tight tolerances for alloys they produce.

Flat Ground:
Any alloy that has “Flat Ground” in the description has been Blanchard ground. Our tolerances for flat grinding are +-.001” across 12”. You can identify Blanchard grinding by circular grind marks. Do not be mislead by other descriptions. Others try to pass off less accurate types of grinding with lower tolerances as flat grinding. This is why we call out our tolerances.

Information Sources:
There are many sources of information regarding knifemaking. Some sources, like Dr. Larrin Thomas of Knife Steel Nerds, are excellent. Other sources are not as credible. It is important to vet the your information sources. Be careful of anyone who says the way to heat treat 1095 or O1 is to heat to non-magnetic and quench in used motor oil. Anyone who publishes this type of information is not credible. When possible, we use information from manufacturers and industry experts.

AI Information:
The latest trend of bad information is from Artificial Intelligence (AI). Multiple companies have AI programs. AI collects and compiles information. The problem is, AI is does not know if the information is accurate or garbage. When asked, AI regurgitates and merges good and bad data. Beware of AI data when researching materials. If you read material information that sounds like it was written by a poetry graduate student, compares materials that are not similar, contains blatantly false information, etc, it was probably AI generated. At AKS, we never use AI to generate material information.

A8 Modified Carbon Steel Information and Composition

Condition:
Our A8 Modified has been properly annealed and is in the soft condition. You do not have to do any non-standard wasteful processes before heat treating. The steel must be heat treated to get to a hardened state. Follow the heat treat recipe and the steel will harden.

Ratings:
75 = Maximum Toughness
35 = Maximum Edge Holding

The rating scale is 0-100, 0 being minimum and 100 being maximum. The ratings are the maximum potential of the alloy. I do not recommend heat treating to the maximum value. Choose a heat treat recipe that results in the attributes you want.

Thank you to Dr Larrin Thomas for all the testing he performed and information he has provided. Buy his book Knife Engineering to learn more about knifemaking.

Description:
A very tough alloy steel. The most common use for this alloy is wood chipper blades. It has extreme toughness with good edge holding.

We do not disclose the mill where this alloy is made. The mill is located in Europe and has very tight tolerances for alloys they produce.

Flat Ground:
Any alloy that has “Flat Ground” in the description has been Blanchard ground. Our tolerances for flat grinding are +-.001” across 12”. You can identify Blanchard grinding by circular grind marks. Do not be mislead by other descriptions. Others try to pass off less accurate types of grinding with lower tolerances as flat grinding. This is why we call out our tolerances.

Information Sources:
There are many sources of information regarding knifemaking. Some sources, like Dr. Larrin Thomas of Knife Steel Nerds, are excellent. Other sources are not as credible. It is important to vet the your information sources. Be careful of anyone who says the way to heat treat 1095 or O1 is to heat to non-magnetic and quench in used motor oil. Anyone who publishes this type of information is not credible. When possible, we use information from manufacturers and industry experts.

AI Information:
The latest trend of bad information is from Artificial Intelligence (AI). Multiple companies have AI programs. AI collects and compiles information. The problem is, AI is does not know if the information is accurate or garbage. When asked, AI regurgitates and merges good and bad data. Beware of AI data when researching materials. If you read material information that sounds like it was written by a poetry graduate student, compares materials that are not similar, contains blatantly false information, etc, it was probably AI generated. At AKS, we never use AI to generate material information.

Data Sheet:
Walter Metals A8 Data Sheet

Beta C Titanium

1084 Carbon Steel Information and Composition

Condition:
Our 1084 has been properly annealed and is in the soft condition. You do not have to do any non-standard wasteful processes before heat treating. The steel must be heat treated to get to a hardened state. Follow the heat treat recipe and the steel will harden.

Ratings:
49 = Maximum Toughness
NT = Maximum Edge Holding

The rating scale is 0-100, 0 being minimum and 100 being maximum. The ratings are the maximum potential of the alloy. If the value shown is "NT", the testing has not been performed. I do not recommend heat treating to the maximum value. Choose a heat treat recipe that results in the attributes you want.

Thank you to Dr Larrin Thomas for all the testing he performed and information he has provided. Buy his book Knife Engineering to learn more about knifemaking.

Description:
A tough high carbon steel. 1084 is suitable for forging or stock removal and is especially good for large knives due to its toughness when heat treated properly.

Flat Ground:
Any alloy that has “Flat Ground” in the description has been Blanchard ground. Our tolerances for flat grinding are +-.001” across 12”. You can identify Blanchard grinding by circular grind marks. Do not be mislead by other descriptions. Others try to pass off less accurate types of grinding with lower tolerances as flat grinding. This is why we call out our tolerances.

Information Sources:
There are many sources of information regarding knifemaking. Some sources, like Dr. Larrin Thomas of Knife Steel Nerds, are excellent. Other sources are not as credible. It is important to vet the your information sources. Be careful of anyone who says the way to heat treat 1095 or O1 is to heat to non-magnetic and quench in used motor oil. Anyone who publishes this type of information is not credible. When possible, we use information from manufacturers and industry experts.

AI Information:
The latest trend of bad information is from Artificial Intelligence (AI). Multiple companies have AI programs. AI collects and compiles information. The problem is, AI is does not know if the information is accurate or garbage. When asked, AI regurgitates and merges good and bad data. Beware of AI data when researching materials. If you read material information that sounds like it was written by a poetry graduate student, compares materials that are not similar, contains blatantly false information, etc, it was probably AI generated. At AKS, we never use AI to generate material information.

1075 Carbon Steel Information and Composition

Condition:
Our 1075 has been properly annealed and is in the soft condition. You do not have to do any non-standard wasteful processes before heat treating. The steel must be heat treated to get to a hardened state. Follow the heat treat recipe and the steel will harden.

Ratings:
76 = Maximum Toughness
NT = Maximum Edge Holding

The rating scale is 0-100, 0 being minimum and 100 being maximum. The ratings are the maximum potential of the alloy. If the value shown is "NT", the testing has not been performed. I do not recommend heat treating to the maximum value. Choose a heat treat recipe that results in the attributes you want.

Thank you to Dr Larrin Thomas for all the testing he performed and information he has provided. Buy his book Knife Engineering to learn more about knifemaking.

Description:
A simple tough high carbon steel. 1075 is suitable for forging or stock removal. 1075 is especially suitable for hard use knives due to its toughness when properly heat treated.

This alloy is similar to 15N20 without 2% nickel.

Flat Ground:
Any alloy that has “Flat Ground” in the description has been Blanchard ground. Our tolerances for flat grinding are +-.001” across 12”. You can identify Blanchard grinding by circular grind marks. Do not be mislead by other descriptions. Others try to pass off less accurate types of grinding with lower tolerances as flat grinding. This is why we call out our tolerances.

Information Sources:
There are many sources of information regarding knifemaking. Some sources, like Dr. Larrin Thomas of Knife Steel Nerds, are excellent. Other sources are not as credible. It is important to vet the your information sources. Be careful of anyone who says the way to heat treat 1095 or O1 is to heat to non-magnetic and quench in used motor oil. Anyone who publishes this type of information is not credible. When possible, we use information from manufacturers and industry experts.

AI Information:
The latest trend of bad information is from Artificial Intelligence (AI). Multiple companies have AI programs. AI collects and compiles information. The problem is, AI is does not know if the information is accurate or garbage. When asked, AI regurgitates and merges good and bad data. Beware of AI data when researching materials. If you read material information that sounds like it was written by a poetry graduate student, compares materials that are not similar, contains blatantly false information, etc, it was probably AI generated. At AKS, we never use AI to generate material information.

1095 Carbon Steel Information and Composition

Condition:
Our 1095 has been properly annealed and is in the soft condition. You do not have to do any non-standard wasteful processes before heat treating. The steel must be heat treated to get to a hardened state. Follow the heat treat recipe and the steel will harden.

Ratings:
22 = Maximum Toughness
31 = Maximum Edge Holding

The rating scale is 0-100, 0 being minimum and 100 being maximum. The ratings are the maximum potential of the alloy. If the value shown is "NT", the testing has not been performed. I do not recommend heat treating to the maximum value. Choose a heat treat recipe that results in the attributes you want.

Thank you to Dr Larrin Thomas for all the testing he performed and information he has provided. Buy his book Knife Engineering to learn more about knifemaking.

One of the best ways to make excellent knives is to use repeatable and reliable processes and materials. 1095 does not meet this criteria. The problem is the specifications are too loose. The composition shown above is for this specific batch of steel.

There are five elements where the acceptable percentage ranges from 0.000% to a maximum of .400%. This is a ridiculous amount of variation. Loose tolerances is the primary reason why we previously chose not to stock 1095 for years.

To get around the problem of loose tolerances we purchased several thousand pounds of 1095 from the same melt. This means you can buy 1095 from us and it will be repeatable and reliable when heat treating. Another way to solve the loose tolerance problem is to buy from high quality mills like Bohler Uddeholm (B/U).

New Knifemakers - I’ve heard many beginning knifemakers say 1095 and O1 are the best steel for beginning knifemakers. When I ask where they learned this information, they almost always say YouTube. Do not believe anyone on YouTube who says 1095 and/or O1 are the best beginner steels. They are wrong. If they are wrong about steel, what other erroneous information are they sharing? In my opinion, the best steel alloys for beginners are 1084, 15N20, 5160, 80CrV2 or 8670. All these steels are much easier to heat treat than 1095 and O1.

I do not recommend 1095 for beginning knifemakers. If you are a new knifemaker and you make a knife with our 1095 that does not get hard, do not complain. You have been warned to use a different steel.

Hamons - Some knifemakers like to use 1095 because they want to make a knife with a hamon. If you want even better hamons, use 26C3 carbon steel.

Quenching - 1095 must be quenched quickly to achieve full hardness. I recommend using Park’s #50 as the quenching oil. Some people recommend quenching in water or brine. These quenchants work, but you can get cracks. The safest, most repeatable and reliable quenching oil is Park’s #50. It is worth the money.

When heat treating 1095, keep your quench tank close to your oven or forge. When the steel is at the correct temperature, remove the blade from the heat source and quench in one smooth, safe motion. Do not delay.  Quench as quickly as possible or you will not achieve full hardness.

Flat Ground:
Any alloy that has “Flat Ground” in the description has been Blanchard ground. Our tolerances for flat grinding are +-.001” across 12”. You can identify Blanchard grinding by circular grind marks. Do not be mislead by other descriptions. Others try to pass off less accurate types of grinding with lower tolerances as flat grinding. This is why we call out our tolerances.

Information Sources:
There are many sources of information regarding knifemaking. Some sources, like Dr. Larrin Thomas of Knife Steel Nerds, are excellent. Other sources are not as credible. It is important to vet the your information sources. Be careful of anyone who says the way to heat treat 1095 or O1 is to heat to non-magnetic and quench in used motor oil. Anyone who publishes this type of information is not credible. When possible, we use information from manufacturers and industry experts.

AI Information:
The latest trend of bad information is from Artificial Intelligence (AI). Multiple companies have AI programs. AI collects and compiles information. The problem is, AI is does not know if the information is accurate or garbage. When asked, AI regurgitates and merges good and bad data. Beware of AI data when researching materials. If you read material information that sounds like it was written by a poetry graduate student, compares materials that are not similar, contains blatantly false information, etc, it was probably AI generated. At AKS, we never use AI to generate material information.

15N20 Carbon Steel Information and Composition

Condition:
Our 15N20 has been properly annealed and is in the soft condition. You do not have to do any non-standard wasteful processes before heat treating. The steel must be heat treated to get to a hardened state. Follow the heat treat recipe and the steel will harden.

Description:
15N20 is a great steel for knife blades. It is very tough and easy to heat treat. It has enough toughness to be used at HRC 61-62 and resist chipping. Its primary use is bandsaw blades in sawmills.

Knifemakers who make damascus are familiar with 15N20. The nickel in 15N20 resists acid etching and stays shiny. This is one reason why 15N20 is used in making some damascus. The nickel also adds significantly to the toughness of the steel.

Flat Ground:
Any alloy that has “Flat Ground” in the description has been Blanchard ground. Our tolerances for flat grinding are +-.001” across 12”. You can identify Blanchard grinding by circular grind marks. Do not be mislead by other descriptions. Others try to pass off less accurate types of grinding with lower tolerances as flat grinding. This is why we call out our tolerances.

Information Sources:
There are many sources of information regarding knifemaking. Some sources, like Dr. Larrin Thomas of Knife Steel Nerds, are excellent. Other sources are not as credible. It is important to vet the your information sources. Be careful of anyone who says the way to heat treat 1095 or O1 is to heat to non-magnetic and quench in used motor oil. Anyone who publishes this type of information is not credible. When possible, we use information from manufacturers and industry experts.

AI Information:
The latest trend of bad information is from Artificial Intelligence (AI). Multiple companies have AI programs. AI collects and compiles information. The problem is, AI is does not know if the information is accurate or garbage. When asked, AI regurgitates and merges good and bad data. Beware of AI data when researching materials. If you read material information that sounds like it was written by a poetry graduate student, compares materials that are not similar, contains blatantly false information, etc, it was probably AI generated. At AKS, we never use AI to generate material information.

440C Stainless Steel Information and Composition

Condition:
Our 440C has been properly annealed and is in the soft condition. You do not have to do any non-standard wasteful processes before heat treating. The steel must be heat treated to get to a hardened state. Follow the heat treat recipe and the steel will harden.

Ratings:
NT = Maximum Toughness
45 = Maximum Edge Holding

The rating scale is 0-100, 0 being minimum and 100 being maximum. The ratings are the maximum potential of the alloy. If the value shown is "NT", the testing has not been performed. I do not recommend heat treating to the maximum value. Choose a heat treat recipe that results in the attributes you want.

Thank you to Dr Larrin Thomas for all the testing he performed and information he has provided. Buy his book Knife Engineering to learn more about knifemaking.

Description:
The highest carbon stainless steel of the 440 series. It is a very good blade steel. I think the reason it is not more popular is because newer steels have overshadowed it.

The mill that makes the ESR 440C located in the United States. They maintain tight tolerances for alloys they produce.

Flat Ground:
Any alloy that has “Flat Ground” in the description has been Blanchard ground. Our tolerances for flat grinding are +-.001” across 12”. You can identify Blanchard grinding by circular grind marks. Do not be mislead by other descriptions. Others try to pass off less accurate types of grinding with lower tolerances as flat grinding. This is why we call out our tolerances.

Information Sources:
There are many sources of information regarding knifemaking. Some sources, like Dr. Larrin Thomas of Knife Steel Nerds, are excellent. Other sources are not as credible. It is important to vet the your information sources. Be careful of anyone who says the way to heat treat 1095 or O1 is to heat to non-magnetic and quench in used motor oil. Anyone who publishes this type of information is not credible. When possible, we use information from manufacturers and industry experts.

AI Information:
The latest trend of bad information is from Artificial Intelligence (AI). Multiple companies have AI programs. AI collects and compiles information. The problem is, AI is does not know if the information is accurate or garbage. When asked, AI regurgitates and merges good and bad data. Beware of AI data when researching materials. If you read material information that sounds like it was written by a poetry graduate student, compares materials that are not similar, contains blatantly false information, etc, it was probably AI generated. At AKS, we never use AI to generate material information.

Data Sheets:
Bohler 440C (N695) Data Sheet
Crucible 440C Data Sheet

440B Stainless Steel Information and Composition

Condition:
Our 440B has been properly annealed and is in the soft condition. You do not have to do any non-standard wasteful processes before heat treating. The steel must be heat treated to get to a hardened state. Follow the heat treat recipe and the steel will harden.

Description:
440B is most famous for being used by Randal Knives as their stainless steel. This stainless steel alloy has less edge holding than 440C but is a little tougher. It is a much better blade steel than 440A.

We do not disclose the mill where this alloy is made. The mill is located in Europe and has very tight tolerances for alloys they produce.

Flat Ground:
Any alloy that has “Flat Ground” in the description has been Blanchard ground. Our tolerances for flat grinding are +-.001” across 12”. You can identify Blanchard grinding by circular grind marks. Do not be mislead by other descriptions. Others try to pass off less accurate types of grinding with lower tolerances as flat grinding. This is why we call out our tolerances.

Information Sources:
There are many sources of information regarding knifemaking. Some sources, like Dr. Larrin Thomas of Knife Steel Nerds, are excellent. Other sources are not as credible. It is important to vet the your information sources. Be careful of anyone who says the way to heat treat 1095 or O1 is to heat to non-magnetic and quench in used motor oil. Anyone who publishes this type of information is not credible. When possible, we use information from manufacturers and industry experts.

AI Information:
The latest trend of bad information is from Artificial Intelligence (AI). Multiple companies have AI programs. AI collects and compiles information. The problem is, AI is does not know if the information is accurate or garbage. When asked, AI regurgitates and merges good and bad data. Beware of AI data when researching materials. If you read material information that sounds like it was written by a poetry graduate student, compares materials that are not similar, contains blatantly false information, etc, it was probably AI generated. At AKS, we never use AI to generate material information.

Data Sheet:
Bohler 440B (N685) Data Sheet

52100 Carbon Steel Information and Composition

Condition:
Our 52100 has been properly annealed and is in the soft condition. You do not have to do any non-standard wasteful processes before heat treating. The steel must be heat treated to get to a hardened state. Follow the heat treat recipe and the steel will harden to the levels shown on the chart.

Ratings:
55 = Maximum Toughness
32 = Maximum Edge Holding

The rating scale is 0-100, 0 being minimum and 100 being maximum. The ratings are the maximum potential of the alloy. I do not recommend heat treating to the maximum value. Choose a heat treat recipe that results in the attributes you want.

Thank you to Dr Larrin Thomas for all the testing he performed and information he has provided. Buy his book Knife Engineering to learn more about knifemaking.

Description:
An excellent high carbon steel. 52100 was developed for use as industrial bearings and has excellent wear resistance and strength. 52100 makes an excellent knife.

Flat Ground:
Any alloy that has “Flat Ground” in the description has been Blanchard ground. Our tolerances for flat grinding are +-.001” across 12”. You can identify Blanchard grinding by circular grind marks. Do not be mislead by other descriptions. Others try to pass off less accurate types of grinding with lower tolerances as flat grinding. This is why we call out our tolerances.

Information Sources:
There are many sources of information regarding knifemaking. Some sources, like Dr. Larrin Thomas of Knife Steel Nerds, are excellent. Other sources are not as credible. It is important to vet the your information sources. Be careful of anyone who says the way to heat treat 1095 or O1 is to heat to non-magnetic and quench in used motor oil. Anyone who publishes this type of information is not credible. When possible, we use information from manufacturers and industry experts.

AI Information:
The latest trend of bad information is from Artificial Intelligence (AI). Multiple companies have AI programs. AI collects and compiles information. The problem is, AI is does not know if the information is accurate or garbage. When asked, AI regurgitates and merges good and bad data. Beware of AI data when researching materials. If you read material information that sounds like it was written by a poetry graduate student, compares materials that are not similar, contains blatantly false information, etc, it was probably AI generated. At AKS, we never use AI to generate material information.

Data Sheet:
Bohler 52100 Data Sheet

8670 Carbon Steel Information and Composition

Condition:
Our 8670 has been properly annealed and is in the soft condition. You do not have to do any non-standard wasteful processes before heat treating. The steel must be heat treated to get to a hardened state. Follow the heat treat recipe and the steel will harden.

Ratings:
100 = Maximum Toughness
  27 = Maximum Edge Holding

The rating scale is 0-100, 0 being minimum and 100 being maximum. The ratings are the maximum potential of the alloy. I do not recommend heat treating to the maximum value. Choose a heat treat recipe that results in the attributes you want.

Thank you to Dr Larrin Thomas for all the testing he performed and information he has provided. Buy his book Knife Engineering to learn more about knifemaking.

Description:
This steel is used extensively in the lumber industry for making large circular saw blades. The nickel add toughness and there is enough carbon for good edge holding. There is not enough nickel to make a good shiny layer in damascus.

All 8670 is not created equal. Our 8670 has been tested to ensure the extreme toughness. Other 8670 cannot make the same claim.

Think of 8670 as an improved version of 5160, extreme toughness and good edge holding.

Our 8670 is not laser or plasma cut. There are no hard edges or heat affected zones.

The tempering temperature curves listed below may raise some concerns. When we received our first batch of 8670, we verified with the mill that the tempering temperatures were correct. We made some knives and used the austenitizing and tempering temperatures the mill recommended. The video below shows a chef knife made from .100" ground to a zero edge being hammered through steel tubing. Finished hardness is 63 RC. The video shows impressive results of using heat treating recommended by the mill.

We do not disclose the mill where this alloy is made. The mill is located in Europe and has very tight tolerances for alloys they produce.

Flat Ground:
Any alloy that has “Flat Ground” in the description has been Blanchard ground. Our tolerances for flat grinding are +-.001” across 12”. You can identify Blanchard grinding by circular grind marks. Do not be mislead by other descriptions. Others try to pass off less accurate types of grinding with lower tolerances as flat grinding. This is why we call out our tolerances.

Information Sources:
There are many sources of information regarding knifemaking. Some sources, like Dr. Larrin Thomas of Knife Steel Nerds, are excellent. Other sources are not as credible. It is important to vet the your information sources. Be careful of anyone who says the way to heat treat 1095 or O1 is to heat to non-magnetic and quench in used motor oil. Anyone who publishes this type of information is not credible. When possible, we use information from manufacturers and industry experts.

AI Information:
The latest trend of bad information is from Artificial Intelligence (AI). Multiple companies have AI programs. AI collects and compiles information. The problem is, AI is does not know if the information is accurate or garbage. When asked, AI regurgitates and merges good and bad data. Beware of AI data when researching materials. If you read material information that sounds like it was written by a poetry graduate student, compares materials that are not similar, contains blatantly false information, etc, it was probably AI generated. At AKS, we never use AI to generate material information.

A11 Carbon Steel Information and Composition

Condition:
Our A11 has been properly annealed and is in the soft condition. You do not have to do any non-standard wasteful processes before heat treating. The steel must be heat treated to get to a hardened state. Follow the heat treat recipe and the steel will harden.

Ratings:
16 = Maximum Toughness
79 = Maximum Edge Holding

The rating scale is 0-100, 0 being minimum and 100 being maximum. The ratings are the maximum potential of the alloy. I do not recommend heat treating to the maximum value. Choose a heat treat recipe that results in the attributes you want.

Thank you to Dr Larrin Thomas for all the testing he performed and information he has provided. Buy his book Knife Engineering to learn more about knifemaking.

Description:
A11 is an amazing steel. It has excellent edge holding.

This alloy It is difficult to work because of its extreme wear resistance. I don't think any knifemaker will offer any finish except for a belt finish. It takes a little more time to sharpen. But once it is sharp it will be sharp for a long long long time.

Flat Ground:
Any alloy that has “Flat Ground” in the description has been Blanchard ground. Our tolerances for flat grinding are +-.001” across 12”. You can identify Blanchard grinding by circular grind marks. Do not be mislead by other descriptions. Others try to pass off less accurate types of grinding with lower tolerances as flat grinding. This is why we call out our tolerances.

Information Sources:
There are many sources of information regarding knifemaking. Some sources, like Dr. Larrin Thomas of Knife Steel Nerds, are excellent. Other sources are not as credible. It is important to vet the your information sources. Be careful of anyone who says the way to heat treat 1095 or O1 is to heat to non-magnetic and quench in used motor oil. Anyone who publishes this type of information is not credible. When possible, we use information from manufacturers and industry experts.

AI Information:
The latest trend of bad information is from Artificial Intelligence (AI). Multiple companies have AI programs. AI collects and compiles information. The problem is, AI is does not know if the information is accurate or garbage. When asked, AI regurgitates and merges good and bad data. Beware of AI data when researching materials. If you read material information that sounds like it was written by a poetry graduate student, compares materials that are not similar, contains blatantly false information, etc, it was probably AI generated. At AKS, we never use AI to generate material information.

Data Sheets:
Bohler A11 (K294) Data Sheet
Crucible A11 (CPM 10V) Data Sheet
Zapp Z-A11 Data Sheet

A2 Carbon Steel Information and Composition

Condition:
Our A2 has been properly annealed and is in the soft condition. You do not have to do any non-standard wasteful processes before heat treating. The steel must be heat treated to get to a hardened state. Follow the heat treat recipe and the steel will harden.

Ratings:
29 = Maximum Toughness
33 = Maximum Edge Holding

The rating scale is 0-100, 0 being minimum and 100 being maximum. The ratings are the maximum potential of the alloy. I do not recommend heat treating to the maximum value. Choose a heat treat recipe that results in the attributes you want.

Thank you to Dr Larrin Thomas for all the testing he performed and information he has provided. Buy his book Knife Engineering to learn more about knifemaking.

Description:
A high carbon alloy steel. A2 is known for taking a very fine keen edge. The chromium provides some corrosion resistance.

We do not disclose the mill where this alloy is made. The mill is located in Europe and has very tight tolerances for alloys they produce.

Flat Ground:
Any alloy that has “Flat Ground” in the description has been Blanchard ground. Our tolerances for flat grinding are +-.001” across 12”. You can identify Blanchard grinding by circular grind marks. Do not be mislead by other descriptions. Others try to pass off less accurate types of grinding with lower tolerances as flat grinding. This is why we call out our tolerances.

Information Sources:
There are many sources of information regarding knifemaking. Some sources, like Dr. Larrin Thomas of Knife Steel Nerds, are excellent. Other sources are not as credible. It is important to vet the your information sources. Be careful of anyone who says the way to heat treat 1095 or O1 is to heat to non-magnetic and quench in used motor oil. Anyone who publishes this type of information is not credible. When possible, we use information from manufacturers and industry experts.

AI Information:
The latest trend of bad information is from Artificial Intelligence (AI). Multiple companies have AI programs. AI collects and compiles information. The problem is, AI is does not know if the information is accurate or garbage. When asked, AI regurgitates and merges good and bad data. Beware of AI data when researching materials. If you read material information that sounds like it was written by a poetry graduate student, compares materials that are not similar, contains blatantly false information, etc, it was probably AI generated. At AKS, we never use AI to generate material information.

Data Sheets:
Bohler A2 Data Sheet
Crucible A2 Data Sheet

AEB-L Stainless Steel Information and Composition

Imitation Alloys:
There are multiple alloys with the same name/composition as AEB-L. We call these alloys "imitations”. The imitators do not perform as well as the original AEB-L from Voestalpine/Bohler/Uddeholm. You can learn more about the original AEB-L vs imitators here.

Condition:
Our AEB-L has been properly annealed and is in the soft condition. You do not have to do any non-standard wasteful processes before heat treating. The steel must be heat treated to get to a hardened state. Follow the heat treat recipe and the steel will harden.

Ratings:
80 = Maximum Toughness
44 = Maximum Edge Holding

The rating scale is 0-100, 0 being minimum and 100 being maximum. The ratings are the maximum potential of the alloy. I do not recommend heat treating to the maximum value. Choose a heat treat recipe that results in the attributes you want.

Thank you to Dr Larrin Thomas for all the testing he performed and information he has provided. Buy his book Knife Engineering to learn more about knifemaking.

Description:
AEB-L was originally developed for razor blades. A few companies have copied the chemical composition of AEB-L. This alloy is formulated with enough carbon for the steel to get very hard but not make any chromium carbides. The extreme fine grain makes them easy to sharpen, have good edge holding, excellent edge stability and toughness.

I've recommended this stainless steel to knifemakers for years. Anyone who has been around me will tell you I love this steel. Try it and let us know what you think of it.

Flat Ground:
Any alloy that has “Flat Ground” in the description has been Blanchard ground. Our tolerances for flat grinding are +-.001” across 12”. You can identify Blanchard grinding by circular grind marks. Do not be mislead by other descriptions. Others try to pass off less accurate types of grinding with lower tolerances as flat grinding. This is why we call out our tolerances.

Information Sources:
There are many sources of information regarding knifemaking. Some sources, like Dr. Larrin Thomas of Knife Steel Nerds, are excellent. Other sources are not as credible. It is important to vet the your information sources. Be careful of anyone who says the way to heat treat 1095 or O1 is to heat to non-magnetic and quench in used motor oil. Anyone who publishes this type of information is not credible. When possible, we use information from manufacturers and industry experts.

AI Information:
The latest trend of bad information is from Artificial Intelligence (AI). Multiple companies have AI programs. AI collects and compiles information. The problem is, AI is does not know if the information is accurate or garbage. When asked, AI regurgitates and merges good and bad data. Beware of AI data when researching materials. If you read material information that sounds like it was written by a poetry graduate student, compares materials that are not similar, contains blatantly false information, etc, it was probably AI generated. At AKS, we never use AI to generate material information.

Data Sheet:
AEB-L Data Sheet

CPM 20CV Stainless Steel Information and Composition

Condition:
Our CPM 20CV has been properly annealed and is in the soft condition. You do not have to do any non-standard wasteful processes before heat treating. The steel must be heat treated to get to a hardened state. Follow the heat treat recipe and the steel will harden.

Ratings:
  8 = Maximum Toughness
61 = Maximum Edge Holding

The rating scale is 0-100, 0 being minimum and 100 being maximum. The ratings are the maximum potential of the alloy. I do not recommend heat treating to the maximum value. Choose a heat treat recipe that results in the attributes you want.

Thank you to Dr Larrin Thomas for all the testing he performed and information he has provided. Buy his book Knife Engineering to learn more about knifemaking.

Description:
Coming Soon

Flat Ground:
Any alloy that has “Flat Ground” in the description has been Blanchard ground. Our tolerances for flat grinding are +-.001” across 12”. You can identify Blanchard grinding by circular grind marks. Do not be mislead by other descriptions. Others try to pass off less accurate types of grinding with lower tolerances as flat grinding. This is why we call out our tolerances.

Information Sources:
There are many sources of information regarding knifemaking. Some sources, like Dr. Larrin Thomas of Knife Steel Nerds, are excellent. Other sources are not as credible. It is important to vet the your information sources. Be careful of anyone who says the way to heat treat 1095 or O1 is to heat to non-magnetic and quench in used motor oil. Anyone who publishes this type of information is not credible. When possible, we use information from manufacturers and industry experts.

AI Information:
The latest trend of bad information is from Artificial Intelligence (AI). Multiple companies have AI programs. AI collects and compiles information. The problem is, AI is does not know if the information is accurate or garbage. When asked, AI regurgitates and merges good and bad data. Beware of AI data when researching materials. If you read material information that sounds like it was written by a poetry graduate student, compares materials that are not similar, contains blatantly false information, etc, it was probably AI generated. At AKS, we never use AI to generate material information.

Data Sheets:
Crucible CPM 20CV Data Sheet
Bohler M390 Data Sheet
Carpenter CTS-204P Data Sheet

K390 Carbon Steel Information and Composition

Condition:
Our K390 has been properly annealed and is in the soft condition. You do not have to do any non-standard wasteful processes before heat treating. The steel must be heat treated to get to a hardened state. Follow the heat treat recipe and the steel will harden.

Ratings:
NT = Maximum Toughness
71 = Maximum Edge Holding

The rating scale is 0-100, 0 being minimum and 100 being maximum. The ratings are the maximum potential of the alloy. If the value shown is "NT", the testing has not been performed. I do not recommend heat treating to the maximum value. Choose a heat treat recipe that results in the attributes you want.

Thank you to Dr Larrin Thomas for all the testing he performed and information he has provided. Buy his book Knife Engineering to learn more about knifemaking.

Description:
Bohler K390 has close to the same edge holding as A11 but is tougher. This steel is difficult to grind, finish and sharpen. Once it is sharp it will stay sharp for a long long time. I wish this steel was more available.

Flat Ground:
Any alloy that has “Flat Ground” in the description has been Blanchard ground. Our tolerances for flat grinding are +-.001” across 12”. You can identify Blanchard grinding by circular grind marks. Do not be mislead by other descriptions. Others try to pass off less accurate types of grinding with lower tolerances as flat grinding. This is why we call out our tolerances.

Information Sources:
There are many sources of information regarding knifemaking. Some sources, like Dr. Larrin Thomas of Knife Steel Nerds, are excellent. Other sources are not as credible. It is important to vet the your information sources. Be careful of anyone who says the way to heat treat 1095 or O1 is to heat to non-magnetic and quench in used motor oil. Anyone who publishes this type of information is not credible. When possible, we use information from manufacturers and industry experts.

AI Information:
The latest trend of bad information is from Artificial Intelligence (AI). Multiple companies have AI programs. AI collects and compiles information. The problem is, AI is does not know if the information is accurate or garbage. When asked, AI regurgitates and merges good and bad data. Beware of AI data when researching materials. If you read material information that sounds like it was written by a poetry graduate student, compares materials that are not similar, contains blatantly false information, etc, it was probably AI generated. At AKS, we never use AI to generate material information.

Data Sheet:
Bohler K390 Data Sheet

CruForgeV Carbon Steel Information and Composition

Condition:
Our CruForgeV has been properly annealed and is in the soft condition. You do not have to do any non-standard wasteful processes before heat treating. The steel must be heat treated to get to a hardened state. Follow the heat treat recipe and the steel will harden.

Ratings:
37 = Maximum Toughness
32 = Maximum Edge Holding

The rating scale is 0-100, 0 being minimum and 100 being maximum. The ratings are the maximum potential of the alloy. I do not recommend heat treating to the maximum value. Choose a heat treat recipe that results in the attributes you want.

Thank you to Dr Larrin Thomas for all the testing he performed and information he has provided. Buy his book Knife Engineering to learn more about knifemaking.

Description:
CruForgeV was developed specifically for forging into knives. Crucible coordinated with knifemakers when developing the steel. The result is an excellent steel that forges and performs very well.

CruForgeV is easy to forge but tougher to finish than any of the 10XX steels or 52100. The tradeoff is edge holding. The vanadium in CruForgeV makes it hold an edge longer than the 10XX steels and 52100.

Flat Ground:
Any alloy that has “Flat Ground” in the description has been Blanchard ground. Our tolerances for flat grinding are +-.001” across 12”. You can identify Blanchard grinding by circular grind marks. Do not be mislead by other descriptions. Others try to pass off less accurate types of grinding with lower tolerances as flat grinding. This is why we call out our tolerances.

Information Sources:
There are many sources of information regarding knifemaking. Some sources, like Dr. Larrin Thomas of Knife Steel Nerds, are excellent. Other sources are not as credible. It is important to vet the your information sources. Be careful of anyone who says the way to heat treat 1095 or O1 is to heat to non-magnetic and quench in used motor oil. Anyone who publishes this type of information is not credible. When possible, we use information from manufacturers and industry experts.

AI Information:
The latest trend of bad information is from Artificial Intelligence (AI). Multiple companies have AI programs. AI collects and compiles information. The problem is, AI is does not know if the information is accurate or garbage. When asked, AI regurgitates and merges good and bad data. Beware of AI data when researching materials. If you read material information that sounds like it was written by a poetry graduate student, compares materials that are not similar, contains blatantly false information, etc, it was probably AI generated. At AKS, we never use AI to generate material information.

Data Sheet:
Crucible CruForgeV Data Sheet

CTS-B75P Blade Steel Information and Composition

D2 Carbon Steel Information and Composition

Condition:
Our D2 has been properly annealed and is in the soft condition. You do not have to do any non-standard wasteful processes before heat treating. The steel must be heat treated to get to a hardened state. Follow the heat treat recipe and the steel will harden.

Ratings:
10 = Maximum Toughness
49 = Maximum Edge Holding

The rating scale is 0-100, 0 being minimum and 100 being maximum. The ratings are the maximum potential of the alloy. I do not recommend heat treating to the maximum value. Choose a heat treat recipe that results in the attributes you want.

Thank you to Dr Larrin Thomas for all the testing he performed and information he has provided. Buy his book Knife Engineering to learn more about knifemaking.

Description:
This steel is almost stainless. Some people say it takes a bad edge and holds it all day long. I disagree with this statement. I think D2 is a great steel that works well in knives. It has good edge holding and low toughness.

Flat Ground:
Any alloy that has “Flat Ground” in the description has been Blanchard ground. Our tolerances for flat grinding are +-.001” across 12”. You can identify Blanchard grinding by circular grind marks. Do not be mislead by other descriptions. Others try to pass off less accurate types of grinding with lower tolerances as flat grinding. This is why we call out our tolerances.

Information Sources:
There are many sources of information regarding knifemaking. Some sources, like Dr. Larrin Thomas of Knife Steel Nerds, are excellent. Other sources are not as credible. It is important to vet the your information sources. Be careful of anyone who says the way to heat treat 1095 or O1 is to heat to non-magnetic and quench in used motor oil. Anyone who publishes this type of information is not credible. When possible, we use information from manufacturers and industry experts.

AI Information:
The latest trend of bad information is from Artificial Intelligence (AI). Multiple companies have AI programs. AI collects and compiles information. The problem is, AI is does not know if the information is accurate or garbage. When asked, AI regurgitates and merges good and bad data. Beware of AI data when researching materials. If you read material information that sounds like it was written by a poetry graduate student, compares materials that are not similar, contains blatantly false information, etc, it was probably AI generated. At AKS, we never use AI to generate material information.

Data Sheets:
Bohler D2 (K110) Data Sheet
Crucible D2 Data Sheet

Elmax Stainless Steel Information and Composition

Condition:
Our Elmax has been properly annealed and is in the soft condition. You do not have to do any non-standard wasteful processes before heat treating. The steel must be heat treated to get to a hardened state. Follow the heat treat recipe and the steel will harden.

Ratings:
24 = Maximum Toughness
55 = Maximum Edge Holding

The rating scale is 0-100, 0 being minimum and 100 being maximum. The ratings are the maximum potential of the alloy. I do not recommend heat treating to the maximum value. Choose a heat treat recipe that results in the attributes you want.

Thank you to Dr Larrin Thomas for all the testing he performed and information he has provided. Buy his book Knife Engineering to learn more about knifemaking.

Description:
Elmax is tougher than S30V and has better edge holding than S35VN. Elmax is made using third generation powder metallurgy stainless steel. The granule size of the metal powder is very small.

Flat Ground:
Any alloy that has “Flat Ground” in the description has been Blanchard ground. Our tolerances for flat grinding are +-.001” across 12”. You can identify Blanchard grinding by circular grind marks. Do not be mislead by other descriptions. Others try to pass off less accurate types of grinding with lower tolerances as flat grinding. This is why we call out our tolerances. All the Elmax we sell is blanchard ground. Learn Why...

Information Sources:
There are many sources of information regarding knifemaking. Some sources, like Dr. Larrin Thomas of Knife Steel Nerds, are excellent. Other sources are not as credible. It is important to vet the your information sources. Be careful of anyone who says the way to heat treat 1095 or O1 is to heat to non-magnetic and quench in used motor oil. Anyone who publishes this type of information is not credible. When possible, we use information from manufacturers and industry experts.

AI Information:
The latest trend of bad information is from Artificial Intelligence (AI). Multiple companies have AI programs. AI collects and compiles information. The problem is, AI is does not know if the information is accurate or garbage. When asked, AI regurgitates and merges good and bad data. Beware of AI data when researching materials. If you read material information that sounds like it was written by a poetry graduate student, compares materials that are not similar, contains blatantly false information, etc, it was probably AI generated. At AKS, we never use AI to generate material information.

Data Sheet:
Uddeholm Elmax Data Sheet

M2 Carbon Steel Information and Composition

Condition:
Our M2 has been properly annealed and is in the soft condition. You do not have to do any non-standard wasteful processes before heat treating. The steel must be heat treated to get to a hardened state. Follow the heat treat recipe and the steel will get hard.

Ratings:
20 = Maximum Toughness
46 = Maximum Edge Holding

The rating scale is 0-100, 0 being minimum and 100 being maximum. The ratings are the maximum potential of the alloy. I do not recommend heat treating to the maximum value. Choose a heat treat recipe that results in the attributes you want.

Thank you to Dr Larrin Thomas for all the testing he performed and information he has provided. Buy his book Knife Engineering to learn more about knifemaking.

Description:
This steel gets very sharp and has good edge holding. M2 has been used by Benchmade and Gerber and is known for its edge holding. The most common use for M2 is to make tools to cut metal. For example, many drill bits are made from M2.

We do not disclose the mill where this alloy is made. The mill is located in Europe and has very tight tolerances for alloys they produce.

Flat Ground:
Any alloy that has “Flat Ground” in the description has been Blanchard ground. Our tolerances for flat grinding are +-.001” across 12”. You can identify Blanchard grinding by circular grind marks. Do not be mislead by other descriptions. Others try to pass off less accurate types of grinding with lower tolerances as flat grinding. This is why we call out our tolerances.